Rigging/Hanging Banner fees are some of the most expensive hourly fees you will pay at a show. These fees will cover the costs to assemble and rig banners, or rig truss over your exhibit. As truss rigging is very complex, depending on your specific needs, we won’t be getting into them here. If your exhibit requires a lighting rig, we strongly suggest you speak with your potential Producers to determine the best budget to allocate based on your needs.
For hanging banners, things are a bit easier to ballpark. As usual, be sure to have your exhibitor service manual handy, as you’ll need it to check on labor rates and regulations. Once you have that, follow the steps below to determine your budget.
- Based on the type of banner you are looking for (pillowcase or SEG), determine how complex your overhead banner frame may be to assemble.
- Pillowcase banners tend to be the easiest to put together. They usually consist of a skeleton framing system similar to a tent that snaps into place. Even the largest of shapes shouldn’t take a couple of assembly laborers more than a couple of hours to put together.
- SEG Banners can be more complex, and their skeletons are usually heavier and require more tools to assemble. Simple shapes may take about twice as long as a similar pillowcase banner, with elaborate shapes possibly taking many hours to assemble. If you plan on doing something very elaborate, estimate two laborers working six hours each to assemble.
- Next, determine the labor required to assemble the fabric portion of your graphic. (Keep in mind that for white or other light-colored banners, it is CRITICAL that your team wears gloves and applies plastic to avoid staining the fabric. This takes more time than assembling dark-colored fabric, which is less vulnerable to dirt staining.)
- For pillowcase banners, mounting the fabric over the frame is typically quick, usually taking less than an hour. But after the fabric is on, your banner may require steaming to remove wrinkles, which can take some time. For larger banners, two laborers may need upwards of an hour or two each to get all wrinkles out.
- For SEG banner fabric is a bit of the opposite of pillowcase banners. Assembling the fabric typically takes longer, as working with SEG can get tricky and tight. A medium sized square banner may take 1-2 hours to install all SEG fabric, depending on how many sides require the SEG. However, SEG graphics rarely need steaming, as their method of construction works very well for pulling out wrinkles.
- Once the banner is assembled, you’ll need a crew to use a condor (also called a “cherry picker” or “snorkel”) to hang your banner. The amount of time required directly correlates to the amount of hanging points your banner requires.
- If you’re going with a lightweight, small—to medium-sized simple shape, you can most likely get away with bridling your banner at the center and hanging it from one point, possibly with a tie-off to prevent the banner from spinning. If this is the case, you should be able to hang your banner at the minimum rate, which is usually one hour.
- If your banner is larger and requires multiple hang points, expect to require more time with your rigging crew. Typically, each hang point requires around 30 minutes to fasten to the convention center ceiling, and then bringing the banner up and leveling off can take another 30 – 60 minutes, depending on the complexity and how easy it is for your condor to navigate your environment.
- Dismantle
- For small to medium banners, figure out the minimum times for dismantling costs. This means the minimum rate for laborers for dismantling your actual sign and the minimum rate for your condor crew, which will be outlined in your show manual.
- For larger setups, costs could exceed 50% of the install time, but typically, even with elaborate banners, dismantle services are much quicker than installation.
If you’d like to use some very rough ballparks, and again, these vary GREATLY all over the country, we recommend you use the following overall cost guidelines, which we’d consider advance and ST rates:
- Small – Medium banners, pillowcase – $2,500
- Small – Medium banners, SEG – $3,500
- Large banners, pillowcase – $5,500
- Large banners, SEG – $7,500
- Large, elaborate banners – $7,500+
Consider that mandatory OT rates can be anywhere from 50% to 100% higher. Consult your exhibitor service manual for specific info regarding your show.
Once again, these vary greatly, with more expensive states most likely running higher and less expensive states running lower. Standard/OT rates will also run higher than this. Lastly, these figures show rates and do not factor in any Producer fees.